Difference between revisions of "Atomic layer deposition"

From LNF Wiki
Jump to navigation Jump to search
Line 9: Line 9:
Below is a general description of the ALD equipment at the LNF. 
====Oxford OpAL ALD====
====Oxford OpAL ALD====

Revision as of 09:36, 3 April 2020

Atomic layer deposition
ALD Small Pic.jpg
Technology Details
Other Names ALD
Technology Deposition
Equipment Oxford ALD,Veeco Fiji ALD

Atomic layer deposition (ALD) is a type of chemical vapor deposition (CVD) where the reactions are limited to the surface of the object being coated. Instead of flowing two or more gasses into the chamber and letting them react on or near the surface of the substrate as in CVD, in ALD the individual chemical components are introduced to the deposition chamber one at a time. Because the reaction is surface-limited, ALD creates extremely conformal films with well controlled thickness. Unfortunately, in order to limit CVD in the chamber, gasses must be pumped out completely between each dose, making the process very slow and only useful for very thin films.


Below is a general description of the ALD equipment at the LNF.

Oxford OpAL ALD

Main article: Oxford OpAL ALD

The Oxford OpAL is a plasma or thermal assisted ALD tool used to deposit Al2O3, ZnO, and HfO. It is an open loop (non-loadlocked) tool which had two channels for metal organic precursors, one channe1 for water and a plasma head.

Veeco Fiji ALD

Main article: Veeco Fiji ALD

The Veeco Fiji is a plasma or thermal assisted ALD tool used to deposit Al2O3, ZnO,TiO2, SiO2, SnO, Pt and HfO. It is a loadlocked tool which has 5 channels for metal organic precursors, one channel for water and a plasma head.

Method of operation

A wafer is placed on a substrate heater in a vacuum chamber and pumped to the mT range. The recipe is then run:

  1. Chamber purge: The chamber is purged with Ar to stabilize chamber temperature and pressure
  2. Dose 1: Precursor 1 dose valve is open - flooding the chamber with precursor. The precursor will stick to all open sites on the substrate
  3. Purge 1: Precursor 1 dose valve is closed and precursor lines are purged with Ar while the gas precursor is pumped away, leaving only the precursor that is reacted on the surface. No gas-phase precursor can be left in the chamber to avoid gas-phase CVD reactions.
  4. Dose 2: Precursor 2 dose valve is open - flooding the chamber with precursor 2 which reacts with precursor 1 to form a film.
  5. Purge 2: Precursor 2 dose valve is closed and again precursor 2 lines are purged with Ar while the gas precursor is pumped away, leaving only the precursor that is reacted on the surface.
  6. Repeat: Steps 2-5 are described as 1 cycle. Each cycle leaves a monolayer (or less) of material on the substrate. The cycles are repeated until desired thickness is met.
  7. Pump Out: Chamber is then pumped out and the recipe is ended.

Tool is then vented and substrate is removed.

An example of this is the common ALD process involving the reaction of Trimethyl Aluminum (TMAl) and Water to grow Al2O3:


  • conformality
  • TSV
  • gate oxides
  • hard coating/protection of complex features

Figures of merit

Deposition rate per cycle

Deposition rate is usually expressed in Å/cycle or nm/cycle as opposed to a rate per time such as Å/second or nm/minute. Once the timing is optimized for a fully saturated, ALD step, the amount deposited per cycle is self-limiting to a monolayer or less of material.

Number of cycles - Standard Process vs Nucleation Delay

ALD processes show a linear deposition rate vs number of cycles so the number of ALD cycles is set to establish the desired thickness. However it can take a few cycles or more for the material to begin to nucleate on the surface and form a continuous film that will promote growth of the next layers. Once it is established nucleation, the film will grow linearly with number of cycles:


Valve timing and Saturation

The timing of the 4 steps of the ALD process need to be set-up for each film and precursor to optimize the process. With dose timing the goal is to saturate the surface with precursor while not overdosing and wasting precursor down the pump line. With the purges, the key is to pump/purge long enough to ensure full removal of any gas reactants but not waste any extra time. In most processes the dose times are extremely short (10ms-1s depending on precursor) while pump times can be longer (5-60s depending on how easy and "sticky" the gasses and byproducts that did not form layers on the substrate are to remove from the chamber.)

In a 2-material process (TMA and water for example) there are two dose steps and two purge steps that must be optimized but each one has the similar responses:

Step Too Short Too Long
Dose No Saturation - less than optimal deposition, not all sites are coated Wasting Precursor, potential CVD
Purge Not all material pumped - CVD - thicker material that does not adhere, coat evenly or reacts differently Wasting time

So a pressure vs time chart for an ideal ALD process is two independent pressure spikes separated by a purge time that is just long enough to purge out all the gas:

During setup of a new precursor, process window recipes are run to determine this ideal dose and purge times. These are usually called saturation curves. TMA dose on the LNF Oxford ALD at 150C show how the dose and purge times were determined for the recipe:

Substrate temperature

Each precursor has a temperature window in which it breaks down into reactive products. Below that temperature the material does not have enough activation energy to react and above that temperature the precursor may decompose or desorb. The window of temperature between these two is often referred to as the ALD window for the precursor.

Within this ALD temperature window, you can process at various temperatures. Generally higher temperature films will deposit less per cycle but can be slightly denser and more pure (although in many cases the films are similar within the temperature window.)

Plasma vs Thermal

Plasma ALD is popular for many materials. Instead of water dosing, an O2 downstream plasma is sent into the chamber to create the reaction. Typically this plasma is remotely generated so it doesn't see the "line of sight" issues associated with a plasma-generated-in-the-chamber PECVD processes.

Plasma has some advantages: First it can create a faster process when large doses of water are needed and the pumping time of the water is slow. The plasma also reduces nucleation delays in some materials and lowers the activation energy needed for some precursors. Finally, plasma can be used to create other chemistries of ALD by injecting Nitrogen, Hydrogen or Ammonia plasmas into the chamber instead of just Oxygen. The disadvantages to plasma are the expense and reliability of the plasma generation equipment and the potential for plasma damage to materials (carbon nanotubes can etch in Oxygen plasma for example.)


ALD can deposit a wide range of materials including metals, metal oxides and metal nitrides. In the LNF the Oxford OpAL is primarily used to deposit Al2O3 while the Veeco Fiji ALD can deposit more films (currently: Al2O3, HfO2, ZnO, TiO2,TiN, Pt, AlN, SiO2)

See also

Further reading