Difference between revisions of "GSI PECVD"
|Line 75:||Line 75:|
|Line 106:||Line 106:|
Revision as of 13:28, 19 May 2015
This article's introduction may be too long for the overall article length.
|Material Processed||SiO2, Si3N3, SiOxNy|
|Sample Size||100mm and Pieces|
|Supported Processes||Standard Processes|
|User Processes||User Processes|
|Warning:||This page has not been released yet.|
The GSI is a Plasma Enhanced Chemical Vapor Deposition (PECVD) system configured to deposit SiO2, Si3N4, and SiOxNy on substrates up to 100mm diameter. This is a single wafer system that deposits film on one side of the substrate at a time. Deposition temperature may range from 100C to 380C. Standard recipes deposit at 200C or 380C. Substrate heating is accomplished with the utilization of a heater block. The heater block does not contain active cooling. This system includes a dual frequency RF power delivery system with 13.56MHz as the primary power component. High frequency utilizes an auto-matching network w/ built in V/I probe on the output and low frequency utilizes a fixed matching network. The 13.56MHz is superimposed onto the 420KHz (when RF1 and RF2 are both used) and is capacitively coupled through the showerhead electrode. A wafer carrier must be used for 100mm and smaller substrates. All component parameters (except temperature) are displayed in system interface as percentage of full scale (ex. RF1 set to 32 is interpreted as 32% of 1000W’s or 320W’s).
- Update this with announcements as necessary
- Standard recipes Oxide 200 and Oxide 380 are optimized for average refractive index of 1.46 +/-0.006.
- Standard recipes Nitr 200 Conv and Nitr 380 Conv are optimized for average refractive index of 2.00 +/-0.006.
- Standard recipe Oxide 200 LS is optimized for low stress (<60MPa for >1um Films)
- Standard recipe Oxide 200 THIN is optimized for minimum porosity of films 1500-5000 angstroms
- Process Chamber utilizes Ebara A70W dry pump, butterfly valve, and 10T Baratron.
- Load-lock utilizes Alcatel ACP 28G dry pump.
- Deposition processes operate between 1.5T to 4.5T
- Heater block 100°C - 380°C
- Comdel dual frequency generator- RF1 1000W 13.56MHz RF2 200W 420kHz
- Advanced Energy Navigator 13.56MHz auto-matching network utilizes variable vacuum capacitors via stepper motors with built-in VI probe at output.
- 420kHz impedance matching is accomplished via stand alone fixed match with the center impedance designed for the conjugate load impedance of the standard Nitride processes.
- 100mm (4") wafers and pieces
- Substrate material:
- Aluminum carrier is used for all runs.
- Maximum substrate thickness is 2mm.
The GSI PECVD is designated as a Semi-Clean class tool. Below is a list of approved materials for the tool. Approved means the material is allowed in the tool under normal circumstances. If a material is not listed, please create a helpdesk ticket or email email@example.com for any material requests or questions.
This section requires expansion.
There are several processes for this tool supported by the LNF, which are described in more detail on the Processes page.
In addition to these, this tool has a number of user-created recipes for etching a wide variety of materials. Some of these recipes are documented on GSI PECVD User Processes. If you are curious if your material can be processed in this tool, please contact the tool engineers via the helpdesk ticket system.
Standard Operating Procedure
Widget text will go here.
- Read through the System Overview and the SOP.
- Create a Helpdesk Ticket requesting training. Please include information on your desired deposition process (films, thicknesses) and a description of your sample (substrate size, substrate material, and materials already present on your sample). Please verify that your substrate material and materials already present on your sample are listed as approved materials in the System Overview.
- A tool engineer will contact you to arrange a time for initial training.
- One or more of these training sessions will be required before a checkout session can be arranged to gain authorization on the tool.
- Request a checkout session with a tool engineer via the helpdesk ticket system. If this checkout is successful, the engineer will authorize you on the tool.
This section requires expansion with: the process name section is blank.
- Chamber maintenance is performed after every 30um's of deposition.
- Following chamber maintenance, a monitor wafer is run on one of the LNF supported standard processes (typically Oxide 200 1500 angstroms) to check tool performance and film characteristics.